4 Inch - Universal Boost Leak Tester Kit - BILLET Aluminum - TURBO BOOST LEAK TESTERS

Boost Leak Tester for your Turbo's Compressor Inlet Flange
Get your boost back!   This boost leak tester is designed to fit over the inlet flange of your turbo charger and allows you to pressurize the turbo and charge system with compressed air while the vehicle is off.  This is an important tool that every turbo car owner needs in their arsenal of tools.  It is going to keep the turbo healthy by eliminating leaks in the boost path and not allowing it to over speed compensating for a boost leak.   It is a must if you are tuned and or going to get a custom tune, or any time you are replacing any components in the intake tract such as charge hoses, intercooler, manifold, vacuum lines, injectors…etc.  Also a must if you are going to the track and want the peace of mind that everything is tight and capable of handling sustained boost without blowing any hoses off Importance of the boost Gauge? Not having a gauge readout on a boost leak test is similar to filling air in your car's tire without a gauge.  You just don't know how much air is in the system!    It is very wise to know how much pressure is actually going into the charge system to prevent damage to your engine and to yourself - Example if the compressor is unregulated (using high pressure shop air at 90 PSI) there is a risk that the charge pipes will be over-pressurized and something will give - the boost leak tester could blow off or any component of the engine could.   Simple Steps to Use the Boost Leak Tester: Remove the intake hose/pipe off your turbo chargers inlet Install the boost leak tester onto the turbo chargers inlet and secure with the T-bolt clamps Pressurize the boost leak tester with an air compressor and a tire inflation tool.   The air compressor should be a minimum of 2 gallon volume.   The larger the compressor, the more capacity you have to fill the engines charge pipes.   A bike pump or electric pump will not supply enough air fast enough to fill the system *Caution! - When filling the system, start with a low pressure around 5 PSI.  Recommended to regulate the compressor to a lower pressure and only increase if filling is too slow.   The boost gauge reading indicates how much compressed air is in the charge pipes. The boost gauge allows you to read the bleed rate of charge pipes when you remove the pressure.   It is normal to see pressure loss average of 1psi every second.  Faster bleed rate at higher pressures and slower bleed rate at lower pressures Listen for leaks.   Use soapy spray if necessary to identify smaller leaks. Fix any leaks points and then retest.  Increase by 5 PSI up to the normal operating boost pressure. Go out and Boost!  Enjoy the restored power from your engine! The gauge on the boost leak tester allows the user to: apply a safe amount of pressure to prevent injury or damage to the charge pipes or engine read how fast the system holds and bleeds air after removing the air source give a good comparison of compressor outlet air Vs. boost test air while pressurizing.  The smaller the difference the lesser the air loss in the system Design Features: Billet 6061 Aluminum End Cap 3" OD with 1/8" NPT threaded gauge port & fitting port High quality silicon coupler 3" height Custom Stainless Steel 30 PSI / 2 Bar Boost Gauge 30 PSI range will give you the appropriate reading when testing your charge pipes for low, medium or high boost levels. Universal Tire Schrader Valve OR Compressor fitting with purchase of extension hose kit (2) Stainless Steel T-Bolt Clamps with Teflon lock-nut ------------------------------------------------------ Option to add an Extension Hose Kit:  Will allow control over shop air and manage the pressure entering into your turbo system.   Mandatory for shop environment where the air compressor is inaccessible.  The ball valve lets you turn on and off the pressure into the system - this can be very important for you to check the decay or bleed rate after filling the system with pressure.   The bleed rate lets you know how well the system holds and this can only be done by cutting off the pressure to the tester. +$35 - Add 3ft Extension Hose with Shut-Off Valve (1) 3 ft. extension hose with stainless on/off valve for easy control All 1/4" NPT Fittings M-Type stainless steel ball valve housing +$45 Add 5ft Ext Hose w/150 PSI Regulator & Shut-Off Valve  (1) 5 ft. Continental extension hose with stainless on/off valve for easy control All 1/4" NPT Fittings M-Type (1) 150 PSI Air Regulator for added safety and control for shop air - aluminum housing Self purging regulator when turning the pressure down stainless steel ball valve housing Lifetime warranty on all components!

GTR R35 Turbo Boost Leak Tester - Turbo Boost Leak Testers

4 Inch - Universal Boost Leak Tester Kit - BILLET Aluminum - TURBO BOOST LEAK TESTERS

2 Turbo Boost Leak Tester Fits Inside 2 Turbo Hose or Intake Hose - Universal Tester Test Kit - Test Upto 30 PSI - Premium - 6061 Aluminum - Restore Power and MPG!

BMW N20 N26 2.0T - BOOST LEAK TESTER Kit - Billet Aluminum 30 PSI - TURBO BOOST LEAK TESTERS

4 Inch - Universal Boost Leak Tester Kit - BILLET Aluminum - TURBO BOOST LEAK TESTERS

Buy Turbo Boost Leak Testers 3 Twin Kit - Universal - Billet Aluminum Online at desertcartZimbabwe

KC Universal KC Boost Leak Detector (300852)

Turbo Boost Leak Testers 4 Universal - Test 4 inch intakes - Slip into Hose or on to Hard Pipe or Turbo Inlet - Premium Components : Automotive

Turbo Boost Leak Testers

turbo pressure tester,Turbo-Test-Kit,Turbo-System-Test-Kit,9-teiliges Turbo-System-Leckage-Tester Turbolader-Luftdruck-Boost-Leck-Test-Kit mit, turbolader luftdruck boost leck test kit

STM Billet Aluminum Boost Leak Tester (STM-UNI-BLT) – MAPerformance

Large Frame Shop Turbo Boost Leak Tester kit 4 5 5.5 6 with 5 ft Extension Air Line Kit with 150 PSI Regulator - TURBO BOOST LEAK TESTERS